4/12/2024 0 Comments Iei keypad manualPanic is activated by pressing the * and # keys at the same time. Some models have 1 Amp form C relays and other models have negative voltage outputs with a 50mA sink.* They can be controlled individually or in combination by a code. You can program these outputs as timed outputs (1 to 90 seconds) or to toggle (latch). See the Wiring Diagram and Specifications for the relay electrical specifications. The main relay is a form C relay, which you can program as a timed output (1 to 90 seconds) or to toggle (latch). The Master Code is always stored in user location one (1). Codes can be 1 to 6 digits in length and digits may be repeated. The Door♦Gard Command and Control keypads allow up to 120 individual user codes. It takes seconds for an authorized user to change codes. LED or sounder guidance makes programming easy. Connect the black wire (V-) to the negative on the strike, and then connect them to the negative on the power supply.Non-volatile EEPROM memory means your codes and instructions will be there whether you remove power for 5 minutes or 5 years.Īll programming is done entirely from the front of the keypad. Connect the green wire (normally open) to the positive on the strike.ģ. Use the following steps to connect the keypad to an electric strike (fail-secure) (see Figure 6 for reference):Ģ. Connect the black wire (V-) to the negative on the Maglock, and then connect them to the negative on the power supply.įigure 5 Wiring the Keypad to a Maglock (Fail-Safe)ĥ.3 Wiring the Keypad to an Electric Strike (Fail-Secure) Connect the gray wire (normally closed) to the positive on the Maglock.ģ. Connect the red wire (V+) to the blue wire (common), and then connect them to the positive on the power supply.Ģ. Use the following steps to connect the keypad to a Maglock (FailSafe):ġ. Access power supply with tamper circuit - board level: 0291100ĥ.2 Wiring the Keypad to a Maglock (Fail-Safe).Access power supply with tamper circuit - in cabinet: 0291200.Using the tamper switch as detailed and connected to the power supply tamper circuit, unauthorized opening of the case or prying the unit off thewall triggers this tamper loop, thus preventing the lock from being released until the reset button is pressed. Both feature a tamper circuit with a reset button mounted on the circuit board. Two models are available: board level and in a cabinet. IEI access system power supplies are designed specifically for access control applications. The diagrams on the next page show the suggested mounting location for each device. Only a Sentrol 3012 or Sentrol 3025T tamper switch can be used. In addition, once the tamper device is activated, it must be configured so that it can only be reset from within the protected area. The lock must be a fail-secure device, meaning the lock remains locked when power is removed. The tamper switch must activate if the keypad is removed from the box and must disconnect power from the lock. To prevent tampering, a tamper switch can be installed in the single gang box used for mounting the keypad. All features referring to the additional relays and outputs are available only on the 242 model.Īlways Triggers (regardless of Door Loop) NOTE: This manual covers both the 212 and 242 model. Both iLW style keypads mount to any standard single-gang electrical box or directly to any wall. Each keypad contains illuminated clear keys that make operation in low light situations easy and accurate. In addition, each keypad uses hardened keys to assure long-term, high-quality performance. The electronics for each keypad are conformal coated in the manufacturing process in order to provide this level of application flexibility. The 212iLW and 242iLW style keypads are designed for both indoor and outdoor flush mount applications. Additionally, the 212iLW keypad provides basic keyless entry by controlling a door locking device where security is not an issue. The output is timed or latched and operated by a user’s PIN code. The 212iLW keypad features a single-relay output to control any device requiring an on/off switch. The 242iLW keypad can control up to four devices, and is perfect for controlling electronic locking devices, security systems, CCTV systems, automatic operators, or machinery. It can perform access control functions and also its four relay outputs can be assigned independently for timed operation or to latch. It has an accessory relay board that provides an additional three relays. The 242iLW keypad features the most flexibility and options available in a self-contained unit. 212iLW/242iLW Standalone Keypad Installation/Programming Manual
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |